Voltage Regulator Earth

Post a reply

Smilies
:D :) ;) :( :o :shock: :? 8-) :lol: :x :P :oops: :cry: :evil: :twisted: :roll: :!: :?: :idea: :arrow: :| :mrgreen: :geek: :ugeek:
BBCode is ON
[img] is ON
[url] is ON
Smilies are ON
Topic review
   

If you wish to attach one or more files enter the details below.

Expand view Topic review: Voltage Regulator Earth

Re: Voltage Regulator Earth

by DevilDog » Sun Nov 24, 2019 4:10 pm

Got it...thanks.

Re: Voltage Regulator Earth

by cass3958 » Sun Nov 24, 2019 3:54 pm

Joe I covered the wiring in this topic http://jagstyperegister.com/forum_new/v ... nator#p802
The wiring was pretty easy once I had worked out what all the wires from the VR were doing and eliminated them all from requirement on the new set up. There is no wiring diagram but I have walked through in this topic where the wires go, their colours and what you need to take out and leave in.

Re: Voltage Regulator Earth

by DevilDog » Sun Nov 24, 2019 3:05 pm

cass3958 wrote: ↑Fri Feb 22, 2019 10:46 pm Orlando I have been looking at my old photos which I have reproduced below. I have now removed my Voltage regulator having converted to the Dynalite alternator but from the photos and memory the earth came from the VR and went down to a self tapping screw which was just below the VR screwed in to the inner wing. You might still have the hole in the inner wing.
The self tapper can be seen in the second photo which has been taken with the VR removed. It is below and between the two lower fixing screws for the VR. The third photo is a close up cropped photo of the screw and its position.
Hope this helps.
Rob, Do you have photos or the wiring diagram used to eliminate your voltage regulator and convert to an alternator?
Thanks,

Re: Voltage Regulator Earth

by Orlando St.R » Sat Feb 23, 2019 9:20 pm

Thanks, Jose. That's very helpful. No, the earth is definitely not redundant. You might, if you had bare metal on the inner wing, get an earth via one of the rubberised mounting posts by chance. But, I know from expensive experience that that little earth tag is definitely needed.

That's a very nice example you have there and thanks for sharing it with us.

Re: Voltage Regulator Earth

by Jose » Sat Feb 23, 2019 12:50 pm

the wire is 6-1/2" inches long, with one copper Spade connector at the regulator end, and one steel Ring connector at the other end.
The measurement is from the end of the spade connector to the end of the Ring connector. It seems this is a redundant Earth because the chassis of the Regulator contacts the body through a mounting screw at the front where there is only 1 mounting screw.


volts-regulator.jpg
volts-regulator.jpg (53.63 KiB) Viewed 2511 times

Re: Voltage Regulator Earth

by Orlando St.R » Sat Feb 23, 2019 10:46 am

Thanks so much, Rob. That's really helpful. Now I look, I do indeed have a hole for a self-tapper in the same place. :)

And, thanks in anticipation, Jose.

Re: Voltage Regulator Earth

by Jose » Fri Feb 22, 2019 11:06 pm

I have a n.o.s. RB340 Regulator and it has a black ground wire connected to the upper spade terminal.

I'll pull it to take pictures and measure the wire.

Re: Voltage Regulator Earth

by cass3958 » Fri Feb 22, 2019 10:46 pm

Orlando I have been looking at my old photos which I have reproduced below. I have now removed my Voltage regulator having converted to the Dynalite alternator but from the photos and memory the earth came from the VR and went down to a self tapping screw which was just below the VR screwed in to the inner wing. You might still have the hole in the inner wing.
The self tapper can be seen in the second photo which has been taken with the VR removed. It is below and between the two lower fixing screws for the VR. The third photo is a close up cropped photo of the screw and its position.
Hope this helps.
Attachments
DSCF6076.jpg
DSCF6076.jpg (3.26 MiB) Viewed 2526 times
DSCF2881.JPG
DSCF2881.JPG (1.53 MiB) Viewed 2526 times
DSCF2881 (2).JPG
DSCF2881 (2).JPG (184.58 KiB) Viewed 2526 times

Voltage Regulator Earth

by Orlando St.R » Fri Feb 22, 2019 7:36 pm

My car came back from restoration without an earth lead to the voltage regulator. What havoc that wreaked with the 123 Ignition Distributor! I've since installed one but I'd like to know where the lead should be routed and where it terminates. Does anyone know/remember? It's the uppermost spade terminal on the regulator. Thanks in anticipation.
WP_20170209_18_21_03_Pro_crop.jpg
WP_20170209_18_21_03_Pro_crop.jpg (193.5 KiB) Viewed 2531 times

Top